Wire (Stainless Steel):ASTM A580/ASTM 580M - AISI Type 304 (Type 316 available on special order) Wire Diameter:9 gauge (.148 or W1.7) or 3/16 (.187 or W2.8) Side Rods and Cross Rods available in any combination of the above. Cross Rods welded 16 O.C. Finishes:Mill Galvanized Coating Hot-Dip Galvanized
ASTM A192 Carbon Steel Seamless Tubes are Low Carbon Steel Tubes with 0.06-0.18 % carbon content with combination of 0.27-0.63 % manganese. These Tubes are also known as mild steel pipes and tubes. ASTM A192 Tubes are low-cost Tubes easy to form and shape. These pipes are manufactured as per ASTM Specification and commercially referred as cs pipes or ms pipes. ASTM A192 Seamless Boiler Tubes ShipmentASTM A192 Standard covers minimum-wall thickness, seamless carbon steel boiler and superheater tubes for high- pressure service. Heat Treatment:Cold -finished tubes shall be heat treated after the final cold finishing at a temperature of 1200°F [650°C] or higher.
Standard Specification for Structural Steel Shapes. 1.1 This specification covers rolled steel structural shapes for use in building framing or bridges, or for general structural purposes. 1.2 Supplementary requirements are provided for use where additional testing or additional restrictions are required by the purchaser. ASTM B209 - 14 Standard Specification for Aluminum and Scope. 1.1 This specification 2 covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys ( Note 1) and tempers shown in Tables 2 and 3, and in the following finishes:(A) Limits are in weight percent maximum unless shown as a range or stated otherwise. (B) Analysis shall be made for the elements for which limits are
Apr 10, 2001 · ASTM A599/A599M-99 - Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet September 10, 1999 - ASTM International 1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. ASTM-B-209-96 - E Corp3.1.5 mill finish sheetshcct having a nonuniform finish which may vary from sheet to shect and within a sheet, and may not be entirely free from stains or oil. 3, 1.6 one-side bright mill finish sheetsheet having a moderate degree of brightness on one side, and a mill finish on the other.
HSS ASTM A500 grade B, Rectangular Fy = 46 ksi, Fu = 58 ksi , Round Fy = 42 ksi, Fu = 58 ksi Pipe ASTM A53 grade B, Fy = 35 ksi, Fu = 60 ksi CONDITION ASD LRFD RELATED INFO Tension 0.6 0.5Fyg u eAFA 0.9 0.75Fyg u eAFA For Ae, see Equation D3-1. Rectangular HSS 0.66FyS 0.99FyS See Note 1. Bending Round HSS, Pipe 0.78FyS 1.17FyS See Note 2. Group of ASTM standards for steel castings and forgings This group of ASTM specifications covers standard properties of steel and iron castings and forgings for valves, flanges, fittings, and other pressure containing parts for high-temperature and low-temperature service. Additionally, in the table below standards for evaluating the microstructure of graphite in iron castings and methods for
astm a992 grade 50 are considered to be the most popular forms of structural rods that act as strong columns and do not pose any threat to your large structures. Known to be made from pure galvanized steel, these astm a992 grade 50 are anti-corrosive and anti-rust and can withstand Manufacturing ASTM A193Manufacturing. The two most common forms of A193 bolts manufactured, stocked, sold, and purchased in the marketplace are either fully threaded studs or heavy hex bolts. B7 studs are the most common product used within this specification. Engineers will specify other configurations of fasteners under the A193 specification, but they are
ASTM A299 is manganese-silicon carbon steel plates for use in welded boilers and other pressure vessels. The grade is A299 Grade A and A299 Grade B SPECIFICATIONSBoard, ASTM C 442/C 442M; and Gypsum Board, CAN/CSA-A82.27-M. 18.104.22.168 Water-Resistant Gypsum Backing Board1. Shall com-ply with Standard Specification for Gypsum Board, ASTM SPECIFICATIONS FOR THE APPLICATION AND FINISHING OF GYPSUM PANEL PRODUCTS 1 ASTM C 1396 is the preferred ASTM reference, ASTM C 36, C 442,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website (astm). Standard Specication for General Requirements for MIL-STD-163 Steel Mill Products, Preparation for Ship-ment and Storage7 MIL-STD-271 Nondestructive Testing Requirements for Metals7 MIL-STD-792 Identication Marking Requirements for Special Purpose Equipment7 2.4 Federal Standard:Fed. Std. No. 183 Continuous Identication Marking of Iron and Steel Products7 2.5 Steel Structures Painting
NOTE 1A typical ordering description is as follows:100 pieces, stainless steel oor plates, 0.1875 by 60 by 120 in., Type 304 (S30400), ASTM 793 XX. 4. Materials and Manufacture 4.1 The steel oor plate material shall conform to the Standard Specication for Steel Bars, Carbon and Alloy Designation:A 29/A 29M 05 Standard Specication for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements for1 This standard is issued under the xed designation A 29/A 29M; the number immediately following the designation indicates the year
2.1 ASTM Standards:2 A 90/A 90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings A 428/A 428M Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles A 902 Terminology Relating to Metallic Coated Steel Prod-ucts A 924/A 924M Specication for General Requirements for Standard Specication for Tin Mill Products, General A01.20 on Tin Mill Products. Current edition approved Jan. 1, 2008. Published January 2008. Originally approved in 1968. Last previous edition approved in 2006 as A 623 - 06a. 2 For referenced ASTM standards, visit the ASTM website, astm, or contact ASTM Customer Service at [email protected] For Annual Book of ASTM
Unitedsteel Plate Factory are specialized in producing and exporting Low alloy and high strength steel plate, heavy plate and wide, heavy plate, Which is a large steel plate supplier mill.. Unitedsteel Plate Factory belongs to Unitedsteel Group, and was invested and established by Hong Kong in 1983. It is the key high-tech enterprise of National Torch Plan, the president the Hot-Dip Process12. Referenced Documents 2.1 ASTM Standards:2 A 90/A 90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings A 308/A 308M Specication for Steel Sheet, Terne (Lead-Tin Alloy) Coated by the Hot-Dip Process
ASTM A299 specification covers manganese-silicon carbon steel plates for use in welded boilers and other pressure vessels. Plates under this specification are produced in two grades (A, B). Yield and tensile strength of Gr. B is higher than Gr. A. Due to high composition of C, Mn, Si. ASTM A299 is widely used for manufacturing pressure and